Sunday, July 14, 2013

Blue butterfly bracelet


Blue Butterfly Bracket Bracelet


*2 strands of blue butterfly brackets
*tube of  translucent light blue beads(or which ever color you prefer)
*tube of dark blue seed beads (to act as spacers)
*bead wire (.18mm in silver)
*Slide-in clasp (silver)
*jump rings (4) (silver)
*clamp beads (6) #1 (silver)
*needle nose pliers
*clamp pliers
*wire cutters
*Measuring tape

*Tip 1- Plan It Out* As with all jewelry designs I laid out the design on my bead board before I started doing anything. Had to try out different style gem stones to see which one matched best, as I did not buy any of the beads at the same time. This also includes making sure the clasp and clamp beads match the color pallet.

*Tip 2- Measure* Always measure for each project to make sure the lengths that fit best are correct. This is important when making items for other people. Once you have done them enough times you will know the required lengths and can skip this step.


- Measure out the length of bead wire you will need to fit around your wrist comfortably and then give yourself about 2 inches to loop back through at the ends. Use wire cutters to cut correct length. Do this again.

-Take a pair of need nose pliers and open a jump ring. Slide the jump ring onto the ring of the clasp and close the jump ring. Do this again for the other ring.

-Repeat this last step for the other side of the clasp. Set aside once done.

*Tip 3- Tight Loops* Try and keep the loop as tight as possible to keep from having a big gap. This can be done by holding one end of the bead wire with a needle nose pliers and then taking the other end of the wire and pulling it tighter. Keeping it tight keeps the wire from rubbing. This is also why using a jump ring to attach to the clasp is important, as the wire attached to the jump ring is not going to move around much if its pulled tight.

 - Take a clamp and thread it on the bead wire; then slide the bead wire through the jump ring attached to the clasp. Loop the bead wire back through the clamp bead and then use the clamp pliers to clamp the bead in place. This should allow for a loop to hold the one end in place. (see *Tip 3*) Do this for both ends.

-Thread on the brackets and beads in the order of the design you picked ahead of time (see *Tip 1* ) Remember to do the same amount for each wire.

-Continue this until you have the length you determined earlier. (see *Tip 2* )

*Suggestion 1* Doing one clamp bead at the end to make sure everything stays tight and then another to create the loop is NOT required. You can choose to use only one clamp bead, just be sure to keep the beads together tightly enough to not end up with large gaps when you wear it. I do it for both ease and strength. Beginners can do this until they get better at re-threading the closure clamp.

*Tip 4 - Consider Material and Purpose* You must always be aware of the type of give and strength your supplies have or you could end up with breaks, scrapping, and no flexibility. The heavier the wire the less bend and flexibility it has. String the beads too tightly together and some will rub together and break. String them too tightly and the beads will bunch and not bend well around your wrist. Some times you need to allow for "give room" with bracelets in order to get the bracelet to wrap.

-Once you have finished your design for the length, slide on a clamp and use the clamp pliers to secure it in place. (see *Suggestion 1* and *Tip 4* ) (set aside for a second)

 - Grab your wire again. Take another clamp bead and thread it on first, then thread the wire through the jump ring on one side of the other end of the clasp. Then thread the wire back through the clamp. Now tighten the wire until you have a small loop. Be sure that the jump ring stays in the loop you create. Use the clamp pliers to close the clamp when you have the loop the size you want. (see *Tip 3* )

-Take a wire cutters and clip off the extra wire as close as possible to the last clamp bead. (If you didn't use two clamp beads you can do this next part.) If the wire is bend-able enough and the bead holes are big enough you can thread the extra wire back through the beads instead of cutting it.

-Repeat the last two steps for the other side of the clasp.

 -That will finish off the bracelet.

No comments:

Post a Comment