Blue butterfly bracelet

 

Blue Butterfly Bracket Bracelet

Supplies:

*2 strands of blue butterfly brackets
*tube of  translucent light blue beads(or which ever color you prefer)
*tube of dark blue seed beads (to act as spacers)
*bead wire (.18mm in silver)
*Slide-in clasp (silver)
*jump rings (4) (silver)
*clamp beads (6) #1 (silver)
*needle nose pliers
*clamp pliers
*wire cutters
*Measuring tape

*Tip 1- Plan It Out* As with all jewelry designs I laid out the design on my bead board before I started doing anything. Had to try out different style gem stones to see which one matched best, as I did not buy any of the beads at the same time. This also includes making sure the clasp and clamp beads match the color pallet.

*Tip 2- Measure* Always measure for each project to make sure the lengths that fit best are correct. This is important when making items for other people. Once you have done them enough times you will know the required lengths and can skip this step.

Steps:

- Measure out the length of bead wire you will need to fit around your wrist comfortably and then give yourself about 2 inches to loop back through at the ends. Use wire cutters to cut correct length. Do this again.

-Take a pair of need nose pliers and open a jump ring. Slide the jump ring onto the ring of the clasp and close the jump ring. Do this again for the other ring.

-Repeat this last step for the other side of the clasp. Set aside once done.

*Tip 3- Tight Loops* Try and keep the loop as tight as possible to keep from having a big gap. This can be done by holding one end of the bead wire with a needle nose pliers and then taking the other end of the wire and pulling it tighter. Keeping it tight keeps the wire from rubbing. This is also why using a jump ring to attach to the clasp is important, as the wire attached to the jump ring is not going to move around much if its pulled tight.

 - Take a clamp and thread it on the bead wire; then slide the bead wire through the jump ring attached to the clasp. Loop the bead wire back through the clamp bead and then use the clamp pliers to clamp the bead in place. This should allow for a loop to hold the one end in place. (see *Tip 3*) Do this for both ends.

-Thread on the brackets and beads in the order of the design you picked ahead of time (see *Tip 1* ) Remember to do the same amount for each wire.

-Continue this until you have the length you determined earlier. (see *Tip 2* )

*Suggestion 1* Doing one clamp bead at the end to make sure everything stays tight and then another to create the loop is NOT required. You can choose to use only one clamp bead, just be sure to keep the beads together tightly enough to not end up with large gaps when you wear it. I do it for both ease and strength. Beginners can do this until they get better at re-threading the closure clamp.

*Tip 4 - Consider Material and Purpose* You must always be aware of the type of give and strength your supplies have or you could end up with breaks, scrapping, and no flexibility. The heavier the wire the less bend and flexibility it has. String the beads too tightly together and some will rub together and break. String them too tightly and the beads will bunch and not bend well around your wrist. Some times you need to allow for "give room" with bracelets in order to get the bracelet to wrap.

-Once you have finished your design for the length, slide on a clamp and use the clamp pliers to secure it in place. (see *Suggestion 1* and *Tip 4* ) (set aside for a second)

 - Grab your wire again. Take another clamp bead and thread it on first, then thread the wire through the jump ring on one side of the other end of the clasp. Then thread the wire back through the clamp. Now tighten the wire until you have a small loop. Be sure that the jump ring stays in the loop you create. Use the clamp pliers to close the clamp when you have the loop the size you want. (see *Tip 3* )

-Take a wire cutters and clip off the extra wire as close as possible to the last clamp bead. (If you didn't use two clamp beads you can do this next part.) If the wire is bend-able enough and the bead holes are big enough you can thread the extra wire back through the beads instead of cutting it.

-Repeat the last two steps for the other side of the clasp.

 -That will finish off the bracelet.

Tear Drop Bracelet

 

Tear Drop Bracelet

Supplies:

*2 strands of tear drop brackets
*tube of translucent light blue beads (or which ever color you prefer)
*bead wire (.18mm in gold)
*Slide-in clasp (gold)
*jump rings (4) (gold)
*clamp beads (6) #1 (gold)
*needle nose pliers
*clamp pliers
*wire cutters
*Measuring tape

*Tip 1- Plan It Out* As with all jewelry designs I laid out the design on my bead board before I started doing anything. Had to try out different style gem stones to see which one matched best, as I did not buy any of the beads at the same time. This also includes making sure the clasp and clamp beads match the color pallet.

*Tip 2- Measure* Always measure for each project to make sure the lengths that fit best are correct. This is important when making items for other people. Once you have done them enough times you will know the required lengths and can skip this step.

Steps:

- Measure out the length of bead wire you will need to fit around your wrist comfortably and then give yourself about 2 inches to loop back through at the ends. Use wire cutters to cut correct length. Do this again.

-Take a pair of need nose pliers and open a jump ring. Slide the jump ring onto the ring of the clasp and close the jump ring. Do this again for the other ring.

-Repeat this last step for the other side of the clasp. Set aside once done.

*Tip 3- Tight Loops* Try and keep the loop as tight as possible to keep from having a big gap. This can be done by holding one end of the bead wire with a needle nose pliers and then taking the other end of the wire and pulling it tighter. Keeping it tight keeps the wire from rubbing. This is also why using a jump ring to attach to the clasp is important, as the wire attached to the jump ring is not going to move around much if its pulled tight.

 - Take a clamp and thread it on the bead wire; then slide the bead wire through the jump ring attached to the clasp. Loop the bead wire back through the clamp bead and then use the clamp pliers to clamp the bead in place. This should allow for a loop to hold the one end in place. (see *Tip 3*) Do this for both ends.

-Thread on the tear drop brackets and beads in the order of the design you picked ahead of time (see *Tip 1* ) Remember to do the same amount for each wire.

-Continue this until you have the length you determined earlier. (see *Tip 2* )

*Suggestion 1* Doing one clamp bead at the end to make sure everything stays tight and then another to create the loop is NOT required. You can choose to use only one clamp bead, just be sure to keep the beads together tightly enough to not end up with large gaps when you wear it. I do it for both ease and strength. Beginners can do this until they get better at re-threading the closure clamp.

*Tip 4 - Consider Material and Purpose* You must always be aware of the type of give and strength your supplies have or you could end up with breaks, scrapping, and no flexibility. The heavier the wire the less bend and flexibility it has. String the beads too tightly together and some will rub together and break. String them too tightly and the beads will bunch and not bend well around your wrist. Some times you need to allow for "give room" with bracelets in order to get the bracelet to wrap.

-Once you have finished your design for the length, slide on a clamp and use the clamp pliers to secure it in place. (see *Suggestion 1* and *Tip 4* ) (set aside for a second)

 - Grab your wire again. Take another clamp bead and thread it on first, then thread the wire through the jump ring on one side of the other end of the clasp. Then thread the wire back through the clamp. Now tighten the wire until you have a small loop. Be sure that the jump ring stays in the loop you create. Use the clamp pliers to close the clamp when you have the loop the size you want. (see *Tip 3* )

-Take a wire cutters and clip off the extra wire as close as possible to the last clamp bead. (If you didn't use two clamp beads you can do this next part.) If the wire is bend-able enough and the bead holes are big enough you can thread the extra wire back through the beads instead of cutting it.

-Repeat the last two steps for the other side of the clasp.

-That will finish off the bracelet.

Key Ring Gem Necklace

Key ring gem necklace

Supplies:
*diamond gems in deep blue
*diamond gems in light blue
*diamond gems in light purple
*clear, or white, seed beads
*Key ring pendant
*bead wire (.18mm in white silver)
*Lobster claw
*jump ring (1) (white silver)
*clamp beads (3) #1 (white silver)
*half inch of small link chain (white silver)
*needle nose pliers
*clamp pliers
*wire cutters
*Measuring tape

*Tip 1- Plan It Out* As with all jewelry designs I laid out the design on my bead board before I started doing anything. Had to try out different style gem stones to see which one matched best, as I did not buy any of the beads at the same time. This also includes making sure the clasp and clamp beads match the color pallet.

*Tip 2- Measure* Always measure for each project to make sure the lengths that fit best are correct. This is important when making items for other people. Once you have done them enough times you will know the required lengths and can skip this step.

Steps:

- Measure out the length of bead wire you will need to fit around your neck comfortably and then give yourself about 2 inches to loop back through at the ends. Use wire cutters to cut correct length.

-Take a pair of need nose pliers and open a jump ring. Slide the jump ring onto the end of the lobster clasp and close the jump ring.

*Tip 3- Tight Loops* Try and keep the loop as tight as possible to keep from having a big gap. This can be done by holding one end of the bead wire with a needle nose pliers and then taking the other end of the wire and pulling it tighter. Keeping it tight keeps the wire from rubbing. This is also why using a jump ring to attach to the clasp is important, as the wire attached to the jump ring is not going to move around much if its pulled tight.

 - Take a clamp and thread it on the bead wire; then slide the bead wire through the jump ring attached to the clasp. Loop the bead wire back through the clamp bead and then use the clamp pliers to clamp the bead in place. This should allow for a loop to hold the one end in place. (see *Tip 3*)

-Thread on the gems in the order of the design you picked ahead of time (see *Tip 1* ).

-Once you get to the middle of the length you determined (see *Tip 1*) slide the pendant on and continue with the pattern.

-Continue this until you have the length you determined earlier. (see *Tip 2* )

*Suggestion 1* Doing one clamp bead at the end to make sure everything stays tight and then another to create the loop is NOT required. You can choose to use only one clamp bead, just be sure to keep the beads together tightly enough to not end up with large gaps when you wear it. I do it for both ease and strength. Beginners can do this until they get better at re-threading the closure clamp.

*Tip 4 - Consider Material and Purpose* You must always be aware of the type of give and strength your supplies have or you could end up with breaks, scrapping, and no flexibility. The heavier the wire the less bend and flexibility it has. String the beads too tightly together and some will rub together and break. String them too tightly and the beads will bunch and not bend well around your wrist. Some times you need to allow for "give room" with bracelets in order to get the bracelet to wrap.

-Once you have finished your design for the length, slide on a clamp and use the clamp pliers to secure it in place. (see *Suggestion 1* and *Tip 4* ) (set aside for a second)

- Use your needle nose pliers to create a half inch length of chain.

 - Grab your wire again. Take another clamp bead and thread it on first, followed by the half inch long chain you just created. Then thread the wire back through the clamp. Now tighten the wire until you have a small loop. Be sure that the chain link stays in the loop you create. Use the clamp pliers to close the clamp when you have the loop the size you want. (see *Tip 3* )

-Take a wire cutters and clip off the extra wire as close as possible to the last clamp bead. (If you didn't use two clamp beads you can do this next part.) If the wire is bend-able enough and the bead holes are big enough you can thread the extra wire back through the beads instead of cutting it.

-That will finish off the necklace.

Double Pearl Elegance

Supplies:

*2 Circle links
*Medium link chain
*Lobster Claw Clasp
*4 large jump rings (to match chain)
*needle nose pliers
*Double string of pearls and gems (Purchased from Michaels)
*Measuring tape

*Tip 1- Plan It Out* As with all jewelry designs I laid out the design on my bead board before I started doing anything. Had to try out different style gem stones to see which one matched best, as I did not buy any of the beads at the same time. This also includes making sure the clasp and clamp beads match the color pallet.

*Tip 2- Measure* Always measure for each project to make sure the lengths that fit best are correct. This is important when making items for other people. Once you have done them enough times you will know the required lengths and can skip this step.

*Tip 3 - Consider Material and Purpose* You must always be aware of the type of give and strength your supplies have or you could end up with breaks, scrapping, and no flexibility. Use large items if you think the smaller version will not allow for flexibility. (i.e. large jump rings over small/medium ones)

 Steps:

-Measure out the length of chain you will need to fit around your neck. (see *Tip 2* )  Use the needle nose pliers to open a link to shorten the chain to your length needed for one side of your neck, and then do it again for the other side. You should have two chain lengths.

-Take a pair of needle nose pliers and open a jump ring. Slide the jump ring onto the end of the lobster claw clasp, then on one end of the chain length you just made, close the jump ring.

- Take a pair of needle nose pliers and open another jump ring. Slide the jump ring onto the end of the other length of chain. Then close the jump ring. This is what the lobster clasp will connect to. 

- Use the needle nose pliers to open a jump ring and attach one end of the chain (either length will do). Then slide on the circle link and close the jump ring.

-Use the needle nose pliers to open another jump ring. Attach the other side of the circle link. Then slide on one side of the double string. Close the jump ring.

-Use the needle nose pliers to open a jump ring and attach one end of the chain (The other one now). Then slide on another circle link and close the jump ring.

-Use the needle nose pliers to open the last jump ring. Attach the other side of the circle link. Then slide on the other side of the double string and close the jump ring.


  -At this point everything should be connected and you have a finished necklace.

 

 

Chain Tower

In June of 2012 I went on vacation to Wisconsin. I went for a family reunion on my Dad's side of the family.
In preparation for the trip I wanted to make some jewelry that would match my outfits. Most of the jewelry I had already made would go with my outfits. I had picked up some more summer colors and I wanted longer necklaces for those outfits.

One has tones of purple and the other has tones of blue and green. They were the first projects I used my chain tower with and it was very helpful. I would highly recommend getting one. It keeps the chain in the same direction so the gems don't face different directions.

Under Water Pearls

Supplies:

*Pearl pendant
*Fresh water pearl tear drops
*sea blue square side gems
* Fresh water 'drop' pearls
*Bright blue oval gems
*bead wire (.18mm in silver)
*jump rings (2)
*clamp beads (3) #1
*needle nose pliers
*clamp pliers
*wire cutters
*Measuring tape
*Lobster clasp and toggle

*Tip 1- Plan It Out* As with all jewelry designs I laid out the design on my bead board before I started doing anything. Had to try out different style gem stones to see which one matched best, as I did not buy any of the beads at the same time. This also includes making sure the clasp, clamp beads, jump rings, and so on match the color pallet.

*Tip 2- Measure* Always measure for each project to make sure the lengths that fit best are correct. This is important when making items for other people. Once you have done them enough times you will know the required lengths and can skip this step.

Steps

- Measure out the length of bead wire you will need to fit comfortably around your neck and sit at the length you like. Then give yourself about 2 inches to loop back through at the ends. Use wire cutters to cut correct length.

- Take a pair of need nose pliers and open a jump ring. Slide the jump ring onto the end of the clasp and close the jump ring.

- Take a clamp and thread it on the bead wire; then slide the bead wire through the jump ring attached to the clasp. Loop the bead wire back through the clamp bead and then use the clamp pliers to clamp it the bead in place. This should allow for a loop to hold the one end in place.

*Tip 3- Tight Loops* Try and keep the loop as tight as possible to keep from having a big gap. This can be done by holding one end of the bead wire with a needle nose pliers and then taking the other end of the wire and pulling it tighter. Keeping it tight keeps the wire from rubbing. This is also why using a jump ring to attach to the clasp is important, as the wire attached to the jump ring is not going to move around much if its pulled tight.

- Thread on the beads and gems in the order of the design you picked ahead of time. (see *Tip 1*)

My design is tear drop pearl, bright blue oval gem, 3 drop pearls (in rotating angle), bright blue oval gem, square sided gem, tear drop pearl, square sided gem, and bright blue oval gem. The only time that changes if when I have reached the middle of the necklace (which I measured and marked ahead of time) where I did square sided gem, oval gem, and then pendant. After that point I reversed the order to mirror the other side.

- Continue this until you have the length you determined earlier. (see *Tip 2* )

*Suggestion 1* Doing one clamp bead at the end to make sure everything stays tight and then another to create the loop is NOT required. You can choose to use only one clamp bead, just be sure to keep the beads together tightly enough to not end up with large gaps when you wear it. I do it for both ease and strength. Beginners can do this until they get better at re-threading the closure clamp.

*Tip 4 - Consider Material and Purpose* You must always be aware of the type of give and strength your supplies have or you could end up with breaks, scrapping, and no flexibility. The heavier the wire the less bend and flexibility it has. String the beads too tightly together and some will rub together and break. String them too tightly and the beads will bunch and not bend well around your wrist. Some times you need to allow for "give room" with bracelets in order to get the bracelet to wrap. This can also mean you should use seed beads to give flex room in between certain types of stones, gems, rocks, and so on. 

- Once you have finished your design for the length, slide on a clamp and use the clamp pliers to secure it in place. (see *Suggestion 1* and *Tip 4* ) (I almost always do this step just to secure my design and tightness of the beads.)

- Take another clamp bead and thread it on first, then slide on the other jump ring, then thread the wire back through the clamp. Now tighten the wire until you have a small loop. Be sure that the jump ring stays in the loop you create. Use the clamp pliers to close the clamp when you have the loop the size you want.  (see *Tip 3* )

- Take a wire cutters and clip off the extra wire as close as possible to the last clamp bead. If the wire is bend-able enough and the bead holes are big enough you can thread the extra wire back through the beads instead of cutting it.

- Take a needle nose pliers and open the jump ring on the end you just finished and slide on the other end of the clasp (Or length of chain if you want to use that instead. This will allow for different tightness around the wrist. This can be very helpful if you didn't follow *Tip 2* and its not long enough to go all the way around the wrist.) and close the jump ring with the needle nose pliers.


That will finish off the necklace.

For some reason I had a considerable amount of left over pearls and gems. With this earring set I did something a little different.

Supplies:

*Fresh water 'drop' pearls (left overs)
*Square side blue gems (left overs)
*Bright blue oval gems (left overs)
*2 1/2 inch length of light silver chain (2)
*Head pins (8)
*Earring 'type' (2)
*Silver wire
*needle nose pliers
*Round nose plier
*wire cutters


*Suggestion 2* When finishing the eye loop you should think ahead to whether you plan to use a jump ring to connect the eye loop, or if you are going to connect straight to the eye loop. If you are going to use a jump ring you can go ahead and close the eye loop. If you aren't going to use a jump ring then you should leave the eye loop open a little in order to connect it to what you want.

- Take a head pin and slide on the gems you have left over that you would like to use in whatever order you have decided. (see *Tip 1*)

- Use the needle nose pliers to bend the head pin at the top of the last gem.

- Use the round nose pliers to create the eye loop. (see *Suggestion 2*)

- Use the wire cutters to remove the extra of the head pin.

- Repeat first 4 steps 8 times, 4 for the square side gems and 4 for the blue oval gems.

- Take the silver wire and cut 6 strips about the length of you pinkie finger.

- Take one strip of wire and thread it through one 'drop' pearl. Pull both ends together (creating a triangle with the tip at the top where the wire ends connect).

- Use the round nose pliers to create a eye loop like you would with a head pin. Instead of cutting off the extra you will wrap the wire around the bottom of the eye loop and just above the pearl.

- Repeat the last step 5 more times.

- Use the needle nose pliers to open the loop on the end of the earring hook. Slide the 1st link of the silver chain on. Close the loop.

- Repeat this step for the other earring.

- Use the needle nose pliers to slide one of the square side gem eye loops onto the 1st link in silver chain. Then use pliers to close the loop.

- Use the needle nose pliers to slide one of the blue oval gem eye loops onto the 4th link in the silver chain. Then use the pliers to close the loop.

- Use the needle nose pliers to slide one of the square side gem eye loops onto the 7th link in the silver chain. Then use the pliers to close the loop.

- Use the needle nose pliers to slide one of the blue oval gem eye loops onto the 10th (or last) link in the silver chain. Then use the pliers to close the loop.

- Repeat the last 4 steps for the other earring.

- Use the needle nose pliers to pull open the 2nd link of the chain. Slide on the pearl eye loop onto the open link. Then use pliers to close the link.

- Use the needle nose pliers to pull open the 6th link of the chain. Slide on the pearl eye loop onto the open link. Then use pliers to close the link.
- Use the needle nose pliers to pull open the 8th link of the chain. Slide on the pearl eye loop onto the open link. Then use pliers to close the link.

- Repeat the last 3 steps for the other earring.


This will finish the earring set.

Sea Rocks, Wear Rocks

Supplies:

*Blue rock gems
*bead wire (.24mm in silver)
*Bubble clasp
*jump rings (2)
*clamp beads (3) #2
*needle nose pliers
*clamp pliers
*wire cutters
*Measuring tape

*Tip 1- Plan It Out* As with all jewelry designs I laid out the design on my bead board before I started doing anything. Had to try out different style gem stones to see which one matched best, as I did not buy any of the beads at the same time. This also includes making sure the clasp and clamp beads match the color pallet.

*Tip 2- Measure* Always measure for each project to make sure the lengths that fit best are correct. This is important when making items for other people. Once you have done them enough times you will know the required lengths and can skip this step.

Steps:

- Measure out the length of bead wire you will need to fit around your wrist and then give yourself about 2 inches to loop back through at the ends. Use wire cutters to cut correct length.

-Take a pair of need nose pliers and open a jump ring. Slide the jump ring onto the end of the clasp and close the jump ring.

- Take a clamp and thread it on the bead wire; then slide the bead wire through the jump ring attached to the clasp. Loop the bead wire back through the clamp bead and then use the clamp pliers to clamp it the bead in place. This should allow for a loop to hold the one end in place.

*Tip 3- Tight Loops* Try and keep the loop as tight as possible to keep from having a big gap. This can be done by holding one end of the bead wire with a needle nose pliers and then taking the other end of the wire and pulling it tighter. Keeping it tight keeps the wire from rubbing. This is also why using a jump ring to attach to the clasp is important, as the wire attached to the jump ring is not going to move around much if its pulled tight.

-Thread on the beads and gems in the order of the design you picked ahead of time (see *Tip 1* )

-Continue this until you have the length you determined earlier. (see *Tip 2* )

*Suggestion 1* Doing one clamp bead at the end to make sure everything stays tight and then another to create the loop is NOT required. You can choose to use only one clamp bead, just be sure to keep the beads together tightly enough to not end up with large gaps when you wear it. I do it for both ease and strength. Beginners can do this until they get better at re-threading the closure clamp.

*Tip 4 - Consider Material and Purpose* You must always be aware of the type of give and strength your supplies have or you could end up with breaks, scrapping, and no flexibility. The heavier the wire the less bend and flexibility it has. String the beads too tightly together and some will rub together and break. String them too tightly and the beads will bunch and not bend well around your wrist. Some times you need to allow for "give room" with bracelets in order to get the bracelet to wrap.  (this is very important for these type of rock gems)

-Once you have finished your design for the length, slide on a clamp and use the clamp pliers to secure it in place. (see *Suggestion 1* and *Tip 4* )

-Take another clamp bead and thread it on first, then slide on the other jump ring, then thread the wire back through the clamp. Now tighten the wire until you have a small loop. Be sure that the jump ring stays in the loop you create. Use the clamp pliers to close the clamp when you have the loop the size you want. (see *Tip 3* )

-Take a wire cutters and clip off the extra wire as close as possible to the last clamp bead. If the wire is bend-able enough and the bead holes are big enough you can thread the extra wire back through the beads instead of cutting it.

-Take a needle nose pliers and open the jump ring on the end you just finished and slide on the other end of the clasp (Or length of chain if you want to use that instead. This will allow for different tightness around the wrist. This can be very helpful if you didn't follow *Tip 2* and its not long enough to go all the way around the wrist.) and close the jump ring with the needle nose pliers.

That will finish off the bracelet.

Seaside on Your Side.

Supplies:

*Round flat pearls
*sea blue square side gems
*bead wire (.18mm in silver)
*Bubble clasp
*jump rings (2)
*clamp beads (3) #1
*needle nose pliers
*clamp pliers
*wire cutters
*Measuring tape

*Tip 1- Plan It Out* As with all jewelry designs I laid out the design on my bead board before I started doing anything. Had to try out different style gem stones to see which one matched best, as I did not buy any of the beads at the same time. This also includes making sure the clasp and clamp beads match the color pallet.

*Tip 2- Measure* Always measure for each project to make sure the lengths that fit best are correct. This is important when making items for other people. Once you have done them enough times you will know the required lengths and can skip this step.

Steps:

- Measure out the length of bead wire you will need to fit around your wrist and then give yourself about 2 inches to loop back through at the ends. Use wire cutters to cut correct length.

-Take a pair of need nose pliers and open a jump ring. Slide the jump ring onto the end of the clasp and close the jump ring.

- Take a clamp and thread it on the bead wire; then slide the bead wire through the jump ring attached to the clasp. Loop the bead wire back through the clamp bead and then use the clamp pliers to clamp it the bead in place. This should allow for a loop to hold the one end in place.

*Tip 3- Tight Loops* Try and keep the loop as tight as possible to keep from having a big gap. This can be done by holding one end of the bead wire with a needle nose pliers and then taking the other end of the wire and pulling it tighter. Keeping it tight keeps the wire from rubbing. This is also why using a jump ring to attach to the clasp is important, as the wire attached to the jump ring is not going to move around much if its pulled tight.

-Thread on the beads and gems in the order of the design you picked ahead of time (see *Tip 1* )

-Continue this until you have the length you determined earlier. (see *Tip 2* )

-Once you have finished your design for the length, slide on a clamp and use the clamp pliers to secure it in place. (see *Suggestion 1* and *Tip 4* ) (I almost always do this step just to secure my design and tightness of the beads.)

*Suggestion 1* Doing one clamp bead at the end to make sure everything stays tight and then another to create the loop is NOT required. You can choose to use only one clamp bead, just be sure to keep the beads together tightly enough to not end up with large gaps when you wear it. I do it for both ease and strength. Beginners can do this until they get better at re-threading the closure clamp.

*Tip 4 - Consider Material and Purpose* You must always be aware of the type of give and strength your supplies have or you could end up with breaks, scrapping, and no flexibility. The heavier the wire the less bend and flexibility it has. String the beads too tightly together and some will rub together and break. String them too tightly and the beads will bunch and not bend well around your wrist. Some times you need to allow for "give room" with bracelets in order to get the bracelet to wrap.

-Take another clamp bead and thread it on first, then slide on the other jump ring, then thread the wire back through the clamp. Now tighten the wire until you have a small loop. Be sure that the jump ring stays in the loop you create. Use the clamp pliers to close the clamp when you have the loop the size you want. (see *Tip 3* )

-Take a wire cutters and clip off the extra wire as close as possible to the last clamp bead. If the wire is bend-able enough and the bead holes are big enough you can thread the extra wire back through the beads instead of cutting it.

-Take a needle nose pliers and open the jump ring on the end you just finished and slide on the other end of the clasp (Or length of chain if you want to use that instead. This will allow for different tightness around the wrist. This can be very helpful if you didn't follow *Tip 2* and its not long enough to go all the way around the wrist.) and close the jump ring with the needle nose pliers.

That will finish off the bracelet.

Earring directions.

Supplies:

*Round flat pearls (left overs)
*Sea blue square side gems (left overs)
*Needle nose pliers
*Round nose pliers
*Wire cutters
*Head pins
*Earring 'type' (2)

*Suggestion 2* When finishing the eye loop you should think ahead to whether you plan to use a jump ring to connect the eye loop, or if you are going to connect straight to the eye loop. If you are going to use a jump ring you can go ahead and close the eye loop. If you aren't going to use a jump ring then you should leave the eye loop open a little in order to connect it to what you want.

- Take a head pin and slide on the pearls/gems you have left over that you would like to use in whatever order you have decided. (see *Tip 1*)

- Use the needle nose pliers to bend the head pin at the top of the last pearl/gem.

- Use the round nose pliers to create the eye loop. (see *Suggestion 2*)

- Use the wire cutters to remove the extra of the head pin.

- Connect eye loop or jump ring (see *Suggestion 2*) to whatever type of earring you chose (I picked a hook earring.)

-Repeat steps to create second earring.

This will finish the earring set.

Fresh water

Supplies:

*Fresh water pearls
*Dark blue gems
*bead wire (.18mm in silver)
*Bubble clasp
*jump rings (2)
*clamp beads (3) #1
*needle nose pliers
*clamp pliers
*wire cutters
*Measuring tape

*Tip 1- Plan It Out* As with all jewelry designs I laid out the design on my bead board before I started doing anything. Had to try out different style gem stones to see which one matched best, as I did not buy any of the beads at the same time. This also includes making sure the clasp and clamp beads match the color pallet.

*Tip 2- Measure* Always measure for each project to make sure the lengths that fit best are correct. This is important when making items for other people. Once you have done them enough times you will know the required lengths and can skip this step.

Steps:

- Measure out the length of bead wire you will need to fit around your wrist and then give yourself about 2 inches to loop back through at the ends. Use wire cutters to cut correct length.

-Take a pair of need nose pliers and open a jump ring. Slide the jump ring onto the end of the clasp and close the jump ring.

- Take a clamp and thread it on the bead wire; then slide the bead wire through the jump ring attached to the clasp. Loop the bead wire back through the clamp bead and then use the clamp pliers to clamp it the bead in place. This should allow for a loop to hold the one end in place.

*Tip 3- Tight Loops* Try and keep the loop as tight as possible to keep from having a big gap. This can be done by holding one end of the bead wire with a needle nose pliers and then taking the other end of the wire and pulling it tighter. Keeping it tight keeps the wire from rubbing. This is also why using a jump ring to attach to the clasp is important, as the wire attached to the jump ring is not going to move around much if its pulled tight.

-Thread on the beads and gems in the order of the design you picked ahead of time (see *Tip 1* )

-Continue this until you have the length you determined earlier. (see *Tip 2* )

-Once you have finished your design for the length, slide on a clamp and use the clamp pliers to secure it in place. (see *Suggestion 1* and *Tip 4* )

*Suggestion 1* Doing one clamp bead at the end to make sure everything stays tight and then another to create the loop is NOT required. You can choose to use only one clamp bead, just be sure to keep the beads together tightly enough to not end up with large gaps when you wear it. I do it for both ease and strength. Beginners can do this until they get better at re-threading the closure clamp.

*Tip 4 - Consider Material and Purpose* You must always be aware of the type of give and strength your supplies have or you could end up with breaks, scrapping, and no flexibility. The heavier the wire the less bend and flexibility it has. String the beads too tightly together and some will rub together and break. String them too tightly and the beads will bunch and not bend well around your wrist. Some times you need to allow for "give room" with bracelets in order to get the bracelet to wrap.

-Take another clamp bead and thread it on first, then slide on the other jump ring, then thread the wire back through the clamp. Now tighten the wire until you have a small loop. Be sure that the jump ring stays in the loop you create. Use the clamp pliers to close the clamp when you have the loop the size you want. (see *Tip 3* )

-Take a wire cutters and clip off the extra wire as close as possible to the last clamp bead. If the wire is bend-able enough and the bead holes are big enough you can thread the extra wire back through the beads instead of cutting it.

-Take a needle nose pliers and open the jump ring on the end you just finished and slide on the other end of the clasp (Or length of chain if you want to use that instead. This will allow for different tightness around the wrist. This can be very helpful if you didn't follow *Tip 2* and its not long enough to go all the way around the wrist.) and close the jump ring with the needle nose pliers.

That will finish off the bracelet.

For some reason I had a considerable amount of left over pearls and gems. With this earring set I did something a little different.

Supplies:

*Fresh water pearls (left overs)
*Dark blue gems (left overs)
*2 1/2 inch length of light silver chain (2)
*Jump rings (2)
*Head pins (16)
*Earring 'type' (2)
*needle nose pliers
*Round nose plier
*wire cutters


*Suggestion 2* When finishing the eye loop you should think ahead to whether you plan to use a jump ring to connect the eye loop, or if you are going to connect straight to the eye loop. If you are going to use a jump ring you can go ahead and close the eye loop. If you aren't going to use a jump ring then you should leave the eye loop open a little in order to connect it to what you want.

- Take a head pin and slide on the pearls/gems you have left over that you would like to use in whatever order you have decided. (see *Tip 1*)

- Use the needle nose pliers to bend the head pin at the top of the last pearl/gem.

- Use the round nose pliers to create the eye loop. (see *Suggestion 2*)

- Use the wire cutters to remove the extra of the head pin.

- Repeat first 3 steps 8 times, 5 for fresh water pearls and 3 for the dark blue gems.

- **Use the needle nose pliers to slide one of the pearl eye loops onto the 2nd link in silver chain. Then use pliers to close the loop.

- Use the needle nose pliers to slide one of the dark blue gem eye loops onto the 4th link in the silver chain. Then use the pliers to close the loop.

- Use the needle nose pliers to slide one of the pearl eye loops onto the 6th link in silver chain. Then use pliers to close the loop.

- Use the needle nose pliers to slide one of the pearl eye loops onto the 7th link in silver chain. Then use pliers to close the loop.

- Use the needle nose pliers to slide one of the dark blue gem eye loops onto the 8th link in the silver chain. Then use the pliers to close the loop.

- Use the needle nose pliers to slide one of the pearl eye loops onto the 8th link in silver chain. Then use pliers to close the loop.

- Use the needle nose pliers to slide one of the dark blue gem eye loops onto the 10th link in the silver chain. Then use the pliers to close the loop.

- Use the needle nose pliers to slide one of the pearl eye loops onto the 12th link in silver chain. Then use pliers to close the loop.

- Use the needle nose pliers to open a jump ring. Slide the first link in the silver chain onto one side of the jump ring. Slide the other side of the jump ring onto to whatever type of earring you chose (I picked a round closure earring.) and then use the needle nose pliers to close jump ring.

-Repeat all steps to create second earring.

This will finish the earring set.

Blue/Black Swirl bracelet

Supplies:
*Blue/black swirl beads
*Black oval gem stones
*bead wire (.18mm in silver)
*bubble pop clasp
*jump rings (2)
*clamp beads (3) #1
*needle nose pliers
*clamp pliers
*wire cutters
*Measuring tape

*Tip 1- Plan It Out* As with all jewelry designs I laid out the design on my bead board before I started doing anything. Had to try out different style gem stones to see which one matched best, as I did not buy any of the beads at the same time.

*Tip 2- Measure* Always measure for each project to make sure the lengths that fit best are correct. This is important when making items for other people. Once you have done them enough times you will know the required lengths and can skip this step.

Steps:

- Measure out the length of bead wire you will need to fit around your wrist and then give yourself about 2 inches to loop back through at the ends. Use wire cutters to cut correct length.

-Take a pair of need nose pliers and open a jump ring. Slide the jump ring onto the end of the clasp and close the jump ring.

- Take a clamp and thread it on the bead wire; then slide the bead wire through the jump ring attached to the clasp. Loop the bead wire back through the clamp bead and then use the clamp pliers to clamp it the bead in place. This should allow for a loop to hold the one end in place.

*Tip 3- Tight Loops* Try and keep the loop as tight as possible to keep from having a big gap. This can be done by holding one end of the bead wire with a needle nose pliers and then taking the other end of the wire and pulling it tighter. Keeping it tight keeps the wire from rubbing. This is also why using a jump ring to attach to the clasp is important, as the wire attached to the jump ring is not going to move around much if its pulled tight.

-Thread on the beads and gems in the order of the design you picked ahead of time (see *Tip 1* )
-Continue this until you have the length you determined earlier. (see *Tip 2* )

-Once you have finished your design for the length, slide on a clamp and use the clamp pliers to secure it in place. (see *Suggestion 1* and *Tip 4* ) (I almost always do this step just to secure my design and tightness of the beads.)

*Suggestion 1* Doing one clamp bead at the end to make sure everything stays tight and then another to create the loop is NOT required. You can choose to use only one clamp bead, just be sure to keep the beads together tightly enough to not end up with large gaps when you wear it. I do it for both ease and strength. Beginners can do this until they get better at rethreading the closure clamp.

*Tip 4 - Consider Material and Purpose* You must always be aware of the type of give and strength your supplies have or you could end up with breaks, scrapping, and no flexibility. The heavier the wire the less bend and flexibility it has. String the beads too tightly together and some will rub together and break. String them too tightly and the beads will bunch and not bend well around your wrist. Some times you need to allow for "give room" with bracelets in order to get the bracelet to wrap.

-Take another clamp bead and thread it on first, then slide on the other jump ring, then thread the wire back through the clamp. Now tighten the wire until you have a small loop. Be sure that the jump ring stays in the loop you create. Use the clamp pliers to close the clamp when you have the loop the size you want. (see *Tip 3* )

-Take a wire cutters and clip off the extra wire as close as possible to the last clamp bead. If the wire is bend-able enough and the bead holes are big enough you can thread the extra wire back through the beads instead of cutting it.

-Take a needle nose pliers and open the jump ring on the end you just finished and slide on the other end of the clasp (Or length of chain if you want to use that instead. This will allow for different tightness around the wrist. This can be very helpful if you didn't follow *Tip 2* and its not long enough to go all the way around the wrist.) and close the jump ring with the needle nose pliers.

That will finish off the bracelet.